Markham Electrical Guide: Unionville Heritage to Tech-Ready New Builds

Markham Electrical Guide: Unionville Heritage to Tech-Ready New Builds

Updated for 2026. Markham contains some of the widest electrical range in the GTA: heritage homes in Unionville with a century of layered wiring, post-war pockets in Wismer and Markham Village, and brand-new smart-ready builds along the Highway 7 tech corridor. A full rewire of an older 1,500 sq ft home runs $8,000–$15,000 — but most Markham homes never need one. Here's the neighbourhood-by-neighbourhood picture.

Two Markhams: heritage main streets and tech-corridor new builds

Drive east on Highway 7 and you can date the housing stock by the electrical work it needs. Around Markham's older cores — Unionville's Main Street heritage district, Markham Village, and the post-war streets between them — you'll find homes from the 1860s through the 1960s: some fully rewired, many partially, with knob-and-tube pockets and generations of additions. Then there's the newer city: Cornell, Greensborough, Box Grove and the condo towers near Highway 7 and the Markham GO, built 2000 onward with 100–200-amp services, structured cabling and EV rough-ins. Two electrical universes, one Markham boundary — and the work I quote looks completely different depending on which one I'm standing in.

What Unionville and older Markham homes hide

In a heritage Unionville home, the panel tells only part of the story. The pattern I expect: original or early knob-and-tube still feeding part of the second floor or attic, cloth-insulated cable spliced to modern Romex somewhere in the walls, a 60- or 100-amp service upgraded once and then loaded to capacity, and outdoor wiring added for porches and carriage-laneway lights that was never meant for Canadian winters. None of this is automatically dangerous — but it all matters for insurance, for adding anything new, and for resale. The fix is usually staged: make the panel and service modern and safe first, then remediate wiring zone by zone as rooms get renovated, with ESA certificates at every stage so the paper trail is as clean as the wiring. In practice that means most Unionville-area owners spend between a few hundred and a few thousand dollars now, and tackle the bigger work when the kitchen or second floor comes apart — rather than writing one enormous cheque for a house they'll renovate anyway.

Pot lights: the work Markham asks for most

If I had to pick one job that defines Markham's electrical demand, it's pot lights — and the room split is remarkably consistent. Kitchens lead because that's where families actually live; open-concept great rooms follow because a single chandelier can't light 600 square feet of combined living space; and finished basements are close behind, since so many Markham families build down before they move up. The chart below shows how our installs split by room.

Pot light demand by room in Markham — lighting installation data for Markham and the GTA
Pot light demand by room (est.). Kitchens and living rooms dominate — most projects we quote include both.

Our pot light and LED lighting installations run $150–$250 per fixture retrofitted, with dimmers and layout included — and the layout conversation matters more in Markham's big open rooms than anywhere else we work.

Living room pot lights and chandelier installed by Bano Electrical Services Ltd in Markham — open-concept lighting
Pot lights and a statement fixture working together — the open-concept formula most Markham living rooms need.

Smart homes, theatres and tech-corridor wiring

The other Markham is defined by what's being added: home theatres and media rooms in the larger new builds, Control4 and whole-home automation for tech-industry homeowners who know exactly what they want, EV chargers in every third garage, and hot tubs and saunas in the bigger lots. New-build electrical is usually solid, but 'builder grade' has real limits — panels with almost no spare breaker spaces, doorbell transformers and networking that an automation system outgrows in a year, and outdoor circuits that assumed a small deck rather than a full backyard kitchen. That's where custom home wiring work pays off: roughing in for what you'll actually use while walls are still accessible, instead of retrofitting premium finishes later.

Home theatre pre-wiring and speaker installation by Bano Electrical Services Ltd in Markham
Home theatre pre-wiring — rough it in during construction or finishing and the result looks effortless.

What electrical work costs in Markham

Honest 2026 ranges for the work we do most here:

JobTypical cost (CAD)
Pot light retrofit (per fixture, installed)$150 – $250
Panel upgrade 100A to 200A$2,800 – $4,500
Full home rewire, 1,500 sq ft older home$8,000 – $15,000
EV charger circuit and install$1,200 – $1,800
Home theatre pre-wire (room)$1,500 – $4,000

Factors that move pricing: heritage construction takes longer to fish and patch, open-renovation timing cuts retrofit costs roughly in half, and Markham's permit pathway through ESA adds a modest, non-negotiable fee every legitimate job includes.

Sources

Markham electrical FAQs

Do Unionville heritage homes have knob and tube wiring?

Many do, at least in pockets — Unionville's housing stock spans well over a century. The visible basement and attic wiring is only part of the picture; finished walls can hide live remnants. A proper inspection with circuit tracing gives you the real map before you renovate or insure.

Is a 100-amp panel enough for a Markham new build?

Builders today install 100–200 amps, and 100 is tight once you add an EV charger, hot tub or basement suite. If your panel is full or your plans include any of those, a load calculation tells you definitively — upgrading before the panel is overloaded is cheaper and easier than after.

What does pot light installation cost in Markham?

Typically $150–$250 per fixture installed in finished drywall, including layout and standard dimmers. A kitchen usually runs $1,200–$2,500 all-in; whole main floors land higher depending on zoning. Rough-in during renovation drops the per-fixture cost noticeably.

Can I automate an older Markham home?

Yes — most automation work is wireless at the device level, with a few wired anchors for reliability. Older homes sometimes need neutral wires added at switches or a panel cleanup first, which we assess up front. The combination of older stock and tech-savvy owners makes Markham one of our biggest automation markets.

Should I get an inspection before buying in Markham?

Absolutely — and specify an electrical inspection, because general home inspectors don't open panels or trace circuits. A $400–$600 electrical inspection on an older Unionville-area purchase has saved buyers five-figure surprises more than once, and it gives you a negotiating document in the deal.

Get a straight quote in Markham

Whether it's a heritage home in Unionville, a pot-light package in Cornell, or a full automation rough-in in a new build, we'll tell you honestly what it takes and what it costs. Free estimates across Markham, Richmond Hill and the GTA — call 416-903-7166.

Free estimates · No obligation

Ready to Book a Licensed Electrician?

Tell us what you need and pick a time that works — we will call you back with a clear, written price.

Call Now Free Estimate